This documentation is for an out-of-date version of Apache Flink. We recommend you use the latest stable version.

Release Notes - Flink 1.7

These release notes discuss important aspects, such as configuration, behavior, or dependencies, that changed between Flink 1.6 and Flink 1.7. Please read these notes carefully if you are planning to upgrade your Flink version to 1.7.

Scala 2.12 support

When using Scala 2.12 you might have to add explicit type annotations in places where they were not required when using Scala 2.11. This is an excerpt from the TransitiveClosureNaive.scala example in the Flink code base that shows the changes that could be required.

Previous code:

val terminate = prevPaths
 .coGroup(nextPaths)
 .where(0).equalTo(0) {
   (prev, next, out: Collector[(Long, Long)]) => {
     val prevPaths = prev.toSet
     for (n <- next)
       if (!prevPaths.contains(n)) out.collect(n)
   }
}

With Scala 2.12 you have to change it to:

val terminate = prevPaths
 .coGroup(nextPaths)
 .where(0).equalTo(0) {
   (prev: Iterator[(Long, Long)], next: Iterator[(Long, Long)], out: Collector[(Long, Long)]) => {
       val prevPaths = prev.toSet
       for (n <- next)
         if (!prevPaths.contains(n)) out.collect(n)
     }
}

The reason for this is that Scala 2.12 changes how lambdas are implemented. They now use the lambda support using SAM interfaces introduced in Java 8. This makes some method calls ambiguous because now both Scala-style lambdas and SAMs are candidates for methods were it was previously clear which method would be invoked.

State evolution

Before Flink 1.7, serializer snapshots were implemented as a TypeSerializerConfigSnapshot (which is now deprecated, and will eventually be removed in the future to be fully replaced by the new TypeSerializerSnapshot interface introduced in 1.7). Moreover, the responsibility of serializer schema compatibility checks lived within the TypeSerializer, implemented in the TypeSerializer#ensureCompatibility(TypeSerializerConfigSnapshot) method.

To be future-proof and to have flexibility to migrate your state serializers and schema, it is highly recommended to migrate from the old abstractions. Details and migration guides can be found here.

Removal of the legacy mode

Flink no longer supports the legacy mode. If you depend on this, then please use Flink 1.6.x.

Savepoints being used for recovery

Savepoints are now used while recovering. Previously when using exactly-once sink one could get into problems with duplicate output data when a failure occurred after a savepoint was taken but before the next checkpoint occurred. This results in the fact that savepoints are no longer exclusively under the control of the user. Savepoint should not be moved nor deleted if there was no newer checkpoint or savepoint taken.

MetricQueryService runs in separate thread pool

The metric query service runs now in its own ActorSystem. It needs consequently to open a new port for the query services to communicate with each other. The query service port can be configured in flink-conf.yaml.

Granularity of latency metrics

The default granularity for latency metrics has been modified. To restore the previous behavior users have to explicitly set the granularity to subtask.

Latency marker activation

Latency metrics are now disabled by default, which will affect all jobs that do not explicitly set the latencyTrackingInterval via ExecutionConfig#setLatencyTrackingInterval. To restore the previous default behavior users have to configure the latency interval in flink-conf.yaml.

Relocation of Hadoop’s Netty dependency

We now also relocate Hadoop’s Netty dependency from io.netty to org.apache.flink.hadoop.shaded.io.netty. You can now bundle your own version of Netty into your job but may no longer assume that io.netty is present in the flink-shaded-hadoop2-uber-*.jar file.

Local recovery fixed

With the improvements to Flink’s scheduling, it can no longer happen that recoveries require more slots than before if local recovery is enabled. Consequently, we encourage our users to enable local recovery in flink-conf.yaml.

Support for multi slot TaskManagers

Flink now properly supports TaskManagers with multiple slots. Consequently, TaskManagers can now be started with an arbitrary number of slots and it is no longer recommended to start them with a single slot.

StandaloneJobClusterEntrypoint generates JobGraph with fixed JobID

The StandaloneJobClusterEntrypoint, which is launched by the script standalone-job.sh and used for the job-mode container images, now starts all jobs with a fixed JobID. Thus, in order to run a cluster in HA mode, one needs to set a different cluster id for each job/cluster.

Scala shell does not work with Scala 2.12

Flink’s Scala shell does not work with Scala 2.12. Therefore, the module flink-scala-shell is not being released for Scala 2.12.

See FLINK-10911 for more details.

Limitations of failover strategies

Flink’s non-default failover strategies are still a very experimental feature which come with a set of limitations. You should only use this feature if you are executing a stateless streaming job. In any other cases, it is highly recommended to remove the config option jobmanager.execution.failover-strategy from your flink-conf.yaml or set it to "full".

In order to avoid future problems, this feature has been removed from the documentation until it will be fixed. See FLINK-10880 for more details.

SQL over window preceding clause

The over window preceding clause is now optional. It defaults to UNBOUNDED if not specified.

OperatorSnapshotUtil writes v2 snapshots

Snapshots created with OperatorSnapshotUtil are now written in the savepoint format v2.

SBT projects and the MiniClusterResource

If you have a sbt project which uses the MiniClusterResource, you now have to add the flink-runtime test-jar dependency explicitly via:

libraryDependencies += "org.apache.flink" %% "flink-runtime" % flinkVersion % Test classifier "tests"

The reason for this is that the MiniClusterResource has been moved from flink-test-utils to flink-runtime. The module flink-test-utils has correctly a test-jar dependency on flink-runtime. However, sbt does not properly pull in transitive test-jar dependencies as described in this sbt issue. Consequently, it is necessary to specify the test-jar dependency explicitly.

Back to top